(AirpurifierMD is a participant in some affiliate programs-we may earn a small fee for referrals at no extra cost to you)

HVAC WHole Home Air Purifier iQair Perfect 16 1200px

Healthier Home? Use your HVAC system as a dream whole home air purifier?

Indoor air pollution is 1.5 to 3.5 times higher than outdoor pollution. In developed countries, we spend 90% of our time inside buildings. HVAC systems are widely used to condition the temperature of the air. Many people wonder if their HVAC system could also be used to purify the air.

As a general rule, an HVAC system’s ability to purify air can be improved with a change of filter. A MERV 16 filter should be used and the system may need to be modified to take bigger filters depending on the size of the home.

In using an HVAC system to purify the air, there are many considerations.

The System Must Have a Filter Made Out of Material-ideally a HEPA Filter

The only way to very efficiently remove particles from the air is to have a filter made of material. There are adverts for electrostatic, photocatalytic oxidation, ionizers, and UV light treatment of air. In general, these are not as good at removing particles from the air as filters with material in them are. Some of them will not remove any particles at all e.g. UV light treatment. An air purifier using photo electrochemical oxidation technology was found by Wirecutter not to be very efficient at all in removing particles from the air-

YouTube video

It is fine to add these technologies to a filter, but please remember it is the material in the filter that is the crucial element of the system. Sometimes the above technologies are sold with less than ideal filters. Marketing sells the science of the non-filter technology. This can distract the customer from the rather indifferent material filter. You are better off not having these technologies if the compromise is a less than ideal material filter.

Some of these technologies also need considerable maintenance. Electrostatic filters which require removing and washing every 2 to 4 weeks.

So you need to base your air purification around a filter made of material. Filters made out of material are either HEPA or MERV.

Filter Quality-HEPA or MERV?

There are two filter standards: one is HEPA (high-efficiency particulate air) and the other is the MERV (minimum efficiency reporting value) grading system.

HEPA filters have much higher efficiency at filtering particles out of the air vending move rated filters. This is shown in the following diagram of the efficiency of removal particles versus particle size. Filters all have the most difficulty in removing particles that are approximately 0.2 um in diameter. As seen a MERV 5 filter filters out very few of these particles a MERV 10 filter filters out any approximately 25% of the particles in MERV 12 filter approximately 60% of these difficult particles and it is only a MERV 16 filter that 95% of the particles this size of filtered out. Conversely, a HEPA filter that will filter out 99.97% of these particles. So, a HEPA filter would ideally be used but if not then at least a Merv 16 filter.

The EPA recommends if you “decide to upgrade or use a higher efficiency filter, choose a filter with at least a minimum efficiency reporting value (MERV) 13 rating, or as higher rating is your system fan and filter slot can accommodate“.

Diagram to give a general idea of the efficiency of filters at various particle sizes (for more precision see this study)
Diagram to give a general idea of the efficiency of filters at various particle sizes (for more precision please see this article)

This is excellent advice, but a MERV 13 filter will only approximately 66% of particles in the size range that filters find most difficult to deal with. A MERV16 filter will remove 95% of these particles and a HEPA filter 99.97% of these particles. So there is good reason to increase the specification of the HVAC filter.

The problem is that more efficient filters need thicker filter media, which obstructs airflow more. If the fan in the HVAC system is only able to pump a small amount of air around the system because of the obstruction of the fan, then it can damage the system. Low airflow in an HVAC system can allow the heating element to overheat and even crack. The element could then leak carbon monoxide into the dwelling. This can be fatal. Low airflow can also damage the cooling coils. If the airflow is not removing the condensing moisture on the coils means that they can ice up – and become encased in a block of ice. Then liquid condensate can flow back into the air conditioning unit and damage it.

HVAC System Fan Needs to Run All the Time That You Are in the House

Usually the fan in an HVAC system will be off when the temperature is within the range set by the thermostat. Over the year, this can be the majority of the time. This would not allow you to use the HVAC system to purify the air, as for much of the time there would be no airflow and hence no purification.

Fortunately, most modern HVAC systems will allow you to leave the fan on continuously. This will cost $300-500 per year more than having the fan on auto mode.

The HVAC System Fan Needs to be Powerful Enough To Provide Required Air Flow

For good air purification, the air in the room needs to be changed five times per hour (for asthmatics eight times per hour)-EPA. A typical HVAC fan will produce 1000 cubic feet of air per minute (cfm), so this would be enough for a dwelling of about 1500 ft.² assuming ceilings are 8 foot high. This output from a typical HVAC fan is when it is using a fairly non-obstructive filter. With a thicker filter, the airflow may be much lower.

So you would need to know how powerful your HVAC fan is in terms of cubic feet per hour of air pumped. This will allow you to assess whether using the existing fan will be powerful enough to supply 5 air changes per hour to your entire home.

Even at a lower rate of air changes per hour there would be some effect and for instance at 2.5 air changes per hour a typical HVAC system would be able to service an area of about 3000 ft2. However the particle count would be higher, there would certainly not be the EPA recommended 80% reduction.

Filter Systems That Are Efficient but Will Not Obstruct Air Flow Too Much

There are 3 solutions to the problem of the filter being efficient but not obstructing the airflow so much that the fan cannot cope with it. These are-

  1. a standard sized more effective filter which is as nonobstructive as possible 
  2. a bypass system in which only some of the air goes through the high efficiency filter
  3. remodeling the HVAC system so that the filter is much larger

1) High Efficiency Filters Standard Sized Filters

Lennox PureAir S (MERV16)

This is the top of the range Lennox unit. It incorporates UV light and a photocatalytic carbon filter. It does not produce ozone. It needs a Lennox S30 thermostat. Installation approximately $2000 + cost of the unit. Nominal airflow capacity is 2000 cubic feet per minute, so it would be suitable for a dwelling of 3000 square feet.

Aprilair 2000 series (MERV 16)

Smaller filters in this range go up to 1600 cfm and so will service an area of 2400 square feet. There is a giant filter outlined in the next section which will need system remodelling.

iQair Nanomax (MERV 16) 

Unique Nano and microfiber filter media and pleat design maximize surface area, giving 5 times the surface area of the standard pleated filter.

The pleated structure of the Nanomax filter
The pleated structure of the Nanomax filter


So this filter provides very low resistance and so virtually no reduction in HVAC airflow. So it does not put a significant strain on your HVAC system. Special wedge-shaped seal so that air does not flow around the filter rather than through it. Custom sizes are available. In a study in schools to protect children from air pollution, AQMD approached 150 manufacturers of which 9 took part in the program. The non-AMEX filter was the only HVAC mounted device that satisfied the performance requirements set by AQMD.


Graph of air pollution showing the decrease in pollution on installing a Nanomax filter. The most important from a health point of view is the PM2.5 (black line)
Graph of air pollution showing the decrease in pollution on installing a Nanomax filter. The most important from a health point of view is the PM2.5 (black line)

2) Bypass Systems

HEPA filters would provide too much resistance to airflow so that the HVAC system is damaged. So to get around this, manufacturers produce bypass systems. With these systems, some air from the return duct flows straight through the HVAC system as normal, but the rest of the air goes through the HEPA filter and then back into the return duct. As only a portion of the air goes through the HEPA filter, it greatly reduces the resistance to airflow. However, this also means that it also reduces the amount of air purified. So these systems only supply enough purified air for relatively small areas. 

Lennox HEPA-60

This is the largest of the Lennox series of HVAC HEPA air filters.  Even this largest model in the range would only be able to perform 3.8 air changes per hour for at home of a 1000 square feet.

Hawk Environmental AirWash Whisper HEPA Filtration System

The largest unit processes 675 cubic feet per minute so suitable for a dwelling of about 1000 square feet.

Further information regarding efficient custom HVAC filters can be found in this article.

3) Systems Providing Increased Filtration Capacity but Needing HVAC system modification.

Aprilair 2000 series (MERV 16)

The largest filter in this series, which has the lowest resistance to flow is the 2516. The highest flow for this model is 2600cfm pressure drop at this flow rate is 0.36 inches water column. At 2000 cfm the pressure drop across the filter is 0.24 inches water column. It is suitable for dwellings up to 4000 square feet.

In view of its size (31 x 28 inches) it will need some reconfiguring of HVAC system. The installation cost will depend on your system but likely to be of the order of $2000.

Filter cost per year $200* (Filter life 6 months Filter cost $100 if buy in a pack of 2) and the filter needs changing every 6 months.

The manufacturer does not specify the degree of removal of ultra-fine particles. These are particles that are so small they can enter our blood stream.

iQair Perfect 16 (MERV 16 and Removes 85% of Ultrafine Particles)

Lowest resistance MERV 16 filter so will put less strain on your HVAC system. Pressure drop 0.22 inches water column at 2000cfm.

Rated airflow 2000 cubic feet per minute so suitable for a dwelling up to 3000 square feet.

IQair HVAC filter in a whole home system
IQair HVAC filter in a whole home system

Installation cost $2700-$3200. Filter Cost per Year $100* (Filter cost $295 Filter life 3 years)

Filter needs changing every 3 years-so the lazy householders option.

Remember to the filter cost needs to be added to the increased cost of the electric power in keeping the fan on continuously $300.

* if you have standalone air purifiers in 3 rooms in your house, it is likely to cost you $300 per year in filters. Also $100 per year in replacement costs for the air purifiers and $100 in electricity. So running costs for separate air purifiers are likely to be in the ballpark of $500 per year.

Further details of the custom features of filter of this HVAC filter system can be found in this post.

NB The size of dwelling calculations are per EPA guidance and assume 8 foot ceilings.

What if These HVAC Filtration Systems Do Not Seem to Filter Enough Air For the Size of Your Home?

Parallel Filtration Systems?

Why not run the systems in parallel? Logically, if you were to run 2 systems in parallel, it would halve the resistance to airflow. This would allow twice the airflow and hence an adequate airflow to a home twice the area. You could even put 3 or possibly more parallel units in. This would enable you to supply a much larger size of home by putting more filter units in parallel. This would be preferable to putting more whole HVAC units in. You would need to check this with your HVAC engineer.

Diagram to illustrate a possible solution to the problem of air flow decreasing when adding more efficient filters to an HVAC system
Diagram to illustrate a possible solution to the problem of air flow decreasing when adding more efficient filters to an HVAC system

Simple HVAC Filter and Additional Air Purification Units

Do the best you can with one of the filters above that will slot into your existing HVAC system. Then have additional air purifiers in the 2-3 rooms that you live in.

Annual costs will be higher, for example, $500 ($400 for air purifiers and $100 for HVAC filters) per year rather than $100 per year for the IQair Perfect 16. If you buy the correct air purifiers and use them properly, you will have somewhat cleaner air in the rooms with air purifiers. However, in the other rooms, the air will be significantly more “dirty”.

Is it Possible to Have an In Duct Air Purifier?

The same effect can be achieved but not by putting an air purifier into a duct. If an air purifier mechanism with fan and filters was put into the duct, the fan would have to activate each time the air conditioning came on. Otherwise the resistance to airflow in the ducting system would likely break the HVAC system. Also, there would be a need for either an air purifier in the duct for each room or for every 2 rooms. This would increase the cost tremendously and also the maintenance with each induct air purifier needing its own filter change every so often. Fortunately, there is an easier approach.

An induct air purifier effect can be achieved by altering the filter unit in the HVAC system for a MERV 16 filter unit and using the HVAC fan to blow the air through the filter. Currently, most HVAC systems will not be able to cope with HEPA filters, but there are designs of MERV16 filters that can be used with existing HVAC systems, as outlined above.

It may be in future that HVAC systems will be designed which can take true HEPA filters-it seems long overdue.

When using HVAC System to Purify Air do Not neglect Other Aspects of Air Purity

t is very easy to get too focused on the HVAC system and neglect to do other things to improve air quality

Simple steps to improve air purity-

  • Ventilate the home with fresh air. Unless you live in a heavily polluted area, opening a window occasionally to bring fresh air in and let polluted air out is a good idea. Also, check the humidity in your home.  
  • Adding plants?? Although this seems a good idea you would need approximately 1000 plants per room to have reduce VOCs. Even then particulate matter in the air would not be reduced.
  • Vacuum regularly with a vacuum cleaner with a HEPA air filter. It is probably best to have a robotic vacuum cleaner so that it is much easier to do this. I know in my house the dust level went down very significantly when we swopped to a robotic vacuum cleaner. Probably weekly.
  • Dust regularly, probably monthly depending on dust levels in your home.
  • Use an extractor fan to extract air to the outside when cooking
  • Consider using an electric induction hob for cooking rather than a gas hob

Also, if possible do not-

  • Air fresheners. Manufacturers of air fresheners are not required to reveal the composition of their “fragrance,” so it is difficult to know what kinds of chemicals the fresheners are putting into the air. Researchers who tested air fresheners have found that some emit toxic or hazardous air pollutants.
  • Scented cleaning products. As much as possible, try to buy unscented detergents, fabric softeners, and other cleaning products. To get a clean scent, use a homemade cleaner with vinegar, baking soda, water, and lemon juice.  
  • Candles or anything else that is burnt in the living space.

What About HVAC Breakdown/Electrical Outage in a Forrest Fire

If you are going to use your HVAC system to purify the air in your home and you live in a very smoke prone area, you may wish to buy a standby air purifier.
 

If There is a Person at Home With a Respiratory Condition

If there is someone with a respiratory illness, then they should have an air purifier in their bedroom. They should also have one in the main room that they spend time in during the day. An air purifier will produce the best possible quality of air for them.-they should not rely on an HVAC.

They should also have the best consumer air purifier possible.

Conclusion

Air purification for an entire home using an HVAC system is feasible. Provided MERV 16 filters are used, the air will have 95% of small particles removed. Provided iQair filters are used also 85% of ultrafine particles will be removed*

HEPA filters in air purifiers will remove 99.97% of small particles. However, standalone air purifiers for a home will have slightly higher ongoing running costs. As the running costs are only slightly higher, it will probably take 20 years for individual air purifiers to become cheaper than remodeling and running an HVAC purification system continuously.

If you go down the individual air purifier route, you should still put a MERV 16 filter in your HVAC system.

So individual air purifiers and a standard MERV16 filter will give slightly better air quality in the rooms with the air purifiers but significantly worse air in the other rooms. 

*Other corporations filters may remove a similar amount of the ultrafine particles but they do not state this in their specifications

(Just as a disclaimer, we're not trying to give you healthcare or medical advice. AipurifierMD is owned and operated by Eljaam Ltd. AirpurifierMD is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. We also participate in other affiliate programs which compensate us for referring traffic.)